Reset Button Emitter Receiver Raintight Photoelectric Switch For Labeling Machine AIA-1 manufacturer from China YUEQING WINSTON ELECTRIC CO.,LTD.

Reset Button Emitter Receiver Raintight Photoelectric Switch For Labeling Machine

Place of Origin:

Guangdong, China (Mainland)


	Add to My Favorites
HiSupplier Escrow	Share \|

Product Detail

Model No.: AIA-1

Reset Button Emitter Receiver Raintight Photoelectric Switch For Labeling Machine

Reset Button Emitter Receiver Raintight Photoelectric Switch For Labeling Machine

Introduction

SN-GDD-1 beam/diffused infrared photoelectric sensor consist of a pair of emitter and receiver installed face to face which compose a circuit. After power is supplied, the receiver will send out an electric signal (NPN/PNP) to the controlled equipment and system when the infrared beam form emitter is blocked by an object.

Application illustration or photoelectric switch

1 . Decection of thick carton

2 . Built-in-power type photoelectric switch

3 . Detecting if beer is affixed with mark or not

4 . Product accounting

5 . Check out the borken strip from carding machine

6 . Check out the broken or faulted tobacco rolling paper

7 . Guard again restrictedc zone being invaded

Photoelectric switch Principle of photoeletric switch

The working principle of the photoelectric switch is that when the beam emitted by the emitter is blocked or partly reflected by the object, the beam by the emitter is blocked or partly reflected by the object, the beam receiver whereby makes a judgment and reacts.

Model composeition and definition of infrared ray photoelectric switch

G 18 3 A 10 N A
—— —— —— —— —— —— —— ——
1 2 3 4 5 6 7 8

No	Composition	Code and definition
1	Basic form	G: infrared ray photoelectric switch
2	Outward appearance code	18,50,76......
3	Working voltage	2.90-250VAC 3:10VDC 4:12-240VDC/24~240VAC 5: Special voltage
4	Detection way	A: diffused reflection type(scattered reflection type) B: feedbace reflection type mirror(mirror reflection type) C: penetration type(correlation type) D: marking detection type G: optical fiber type
5	Detection distance	05:5cm 10:10cm 30:30cm 101:10cm
6	Output form	N: NPN transistor output P: PNP transistor output J: Relay contact output L: AC two-wire output S: With two outputs;NPN and PNP
7	Output state	A: Normally open(light entering NO) B:Normally close(light sheltering NC) C:normally open+normally close
8	Subsidiary	T1: front delay T2:rear delay Y:oil proof T:with aviiation connector I: special requirement

That indicates the infrared ray photoelectric switch of M18 cylinder,DC 10-30V working voltage, diffused reflection type, detection distance 10cm, and NPN normally open type.

Detection way	5000mm(beam)	Output current	<=80mA(DC12V)
Detection distance	800mm(reflection)	Ambient temperature	In use -25-------+55
Detection distance	infrared(920mm)	Ambient temperature	At stock -4-------+55
Light source(wavelength)	<=30	Lead length	Emitter,receiver both 2m
Point angle	6-36VDC	Output	NPN or PNP transistpr output
Supply voltage	Beam type of reflective type	Protection level	IP67(IEC60529)
Residual voltage	DC(3-wire):<=1.5VDC AC(2-wire):<=12VDC	Withstanding voltage	1500VAC 50/60Hz(one minute)
Insulation resistance	>=50MΩ Min(500VDC Mega)	Impact resistance	500M/S(50G2)X,Y,Z(3 times in each direction)
Temperature effect	Within -25-+70,less than 10% compared with the detection range at +25	Vibration resistance	10-55Hz(cycles per min.) (complex amplitude)1mm,X,Y,Z(2 hours in each direction)